Gen2 projectors DIY?
lockstock 15 May 2012
got the wiring around the correct way (99% sure) changed the low beam globes but still the drivers side low beam wont cooperate. must be an issue with the connections, maybe the soldering. the project continues
Octane 05 Aug 2012
So OzLib has gone down. Does anyone have a link to another DIY? I'm half way through this conversion atm and starting to do this
Octane 09 Aug 2012
Bumping again, I found the mDIY guide on SLi helpful, but I had some trouble getting the low beams to stay on when the highs were switched on.
Basically, all the wires are the same colours on the stanard and JDM spec lights, so its just a case of splicing them to the correct colour wire on the JDM headlight plug. That was easy.
But, all the guides and DIY's say to earth out the low beam wire (yellow one) direct to the chassis. When I did this, I had no parkers or low beams, no matter which lights were switched on. So I've put it back to the original wiring config for the time being.
Can someone confirm exactly which wire, and where needs to be grounded? Also, at what point do I ground it? Straight from the headlight globe to the chassis? Or before the plug?
Basically, all the wires are the same colours on the stanard and JDM spec lights, so its just a case of splicing them to the correct colour wire on the JDM headlight plug. That was easy.
But, all the guides and DIY's say to earth out the low beam wire (yellow one) direct to the chassis. When I did this, I had no parkers or low beams, no matter which lights were switched on. So I've put it back to the original wiring config for the time being.
Can someone confirm exactly which wire, and where needs to be grounded? Also, at what point do I ground it? Straight from the headlight globe to the chassis? Or before the plug?
Adam 09 Aug 2012
I can have a look for you on the weekend.
I remember i had the same problem and had to ground a different wire.
Have you got a wiring diagram for the car?
I remember i had the same problem and had to ground a different wire.
Have you got a wiring diagram for the car?
Octane 09 Aug 2012
Yep, have the full wiring diagams for the whole car, and printouts of a couple of different DIY's. Grounding the low-beam didn't make sense to me, as it looks like the relay is on the ground wire, so earthing it between the light and the relay would mean you'd never get a circuit.
Somehow you need to create a circuit in the low-beam loop from the high beam circuit. I'll take another look at the wiring diagram and see what I can figure out.
Somehow you need to create a circuit in the low-beam loop from the high beam circuit. I'll take another look at the wiring diagram and see what I can figure out.
Adam 09 Aug 2012
Okay, This is a pic for clarity (wired up slightly wrong and passanger side)
Then this is the pic I took today (drivers side)
The plug on the LHS is going into the lights.
Then this is the pic I took today (drivers side)
The plug on the LHS is going into the lights.
Octane 09 Aug 2012
Yeah that's what I thought, yellow wire earthed out... Don't know why it isn't working on mine when I earth it though.
Ah well, at least I have the lights in and working as standard. I'll try to figure it out laterz and report back.
Thanks again for the photo's Adam.
Ah well, at least I have the lights in and working as standard. I'll try to figure it out laterz and report back.
Thanks again for the photo's Adam.
Adam 09 Aug 2012
Maybe your earth point wasn't good enough? Can you try jumping it to the neg on the battery to eliminate that?
Robert 20 Nov 2013
My projectors are still wired up wrong, low beam turns off when the high beam turns on.
Adam you need to show me where I went wrong.
Robert 20 Nov 2013
Ill have to compare it to my wiring, failing that you can show me at ichibarn (if your going)