My B4 now with moar lip!
#1
Posted 14 May 2010 - 06:47 PM
I decided to try the MY06-07 Wrx Sti Lip as I know of a couple of other B4's that have used a similar style and look awesome.
http://www.ultrex.co...my07-p-278.html
I knew it was never going to be bolt on job and Rob at Ultrex informed me of this also. In terms of how true this was- I only was able to use 1 screw hole that actually lined up between the lip and the bumper and that was the centre hole!! Every other hole in both the lip and bumper had to be drilled to get the lip to fit "just right".
As I dont have a proper jack or car ramp I ended up jacking the car up alternating either side probably about 5-6 times to line everything up before i drilled into anything. The lip turned out to be about an inch and a half too long in terms of where it ended at the guard. So I also had to cut off the excess (including little end plates). I had originally intended to glue these end plates back on, but after fiddling around with them for a while I decided it looks just fine without them.
So here are a couple of pics that I only just got in before the sun went down, so I will get some better pics tomorrow. Excuse the badly stone chipped front bar!!
Needless to say the front end looks TOUGH and I am very happy with the end result. Not bad for $180.
Ecutek Stage 2, 3" DBE, Walbro FP, Hyperflow CAI
14.2 @ 158kph
#2
Posted 14 May 2010 - 06:57 PM
Ugh i could ramble on for forking days about this stuff.
#3
Posted 14 May 2010 - 07:27 PM
Subyclub, The place where random internet weirdos become good mates
#4
Posted 14 May 2010 - 07:59 PM
#5
Posted 14 May 2010 - 08:18 PM
Ecutek Stage 2, 3" DBE, Walbro FP, Hyperflow CAI
14.2 @ 158kph
#6
Posted 14 May 2010 - 09:34 PM
I should just convert to single, right?As soon as she hands it to you, slowly take of your pants, then, while staring her straight in the eyes rub it against the tip of you penis, while continuing your painfully intense gaze whisper to her;
"My eye is watering, this might be a bit hot"
Horsepower Factory
Revzone Auto Tuning Centre
#7
Posted 14 May 2010 - 10:01 PM
#8
Posted 15 May 2010 - 12:15 AM
#9
Posted 15 May 2010 - 08:13 AM
#10
Posted 15 May 2010 - 10:57 AM
#11
Posted 15 May 2010 - 10:57 AM
If I told you I was a compulsive liar, would you believe me?
#12
Posted 15 May 2010 - 11:04 AM
#13
Posted 15 May 2010 - 03:30 PM
#14
Posted 15 May 2010 - 06:27 PM
Ecutek Stage 2, 3" DBE, Walbro FP, Hyperflow CAI
14.2 @ 158kph
#15
Posted 16 May 2010 - 10:19 PM
OEM+
#16
Posted 13 February 2011 - 08:09 PM
#17
Posted 13 February 2011 - 08:29 PM
The company is based in Perth, send them an email or message via eBay, they might have one..
I'm ready to buy one for my gen iv GT
#18
Posted 13 February 2011 - 10:24 PM
loose the liberty.asn.au numberplate frames, and you'll gain another 10 of awesome.
#19
Posted 13 February 2011 - 11:22 PM
Ecutek Stage 2, 3" DBE, Walbro FP, Hyperflow CAI
14.2 @ 158kph
#20
Posted 26 May 2011 - 12:32 PM
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users